/ / /

Avocent AVRIQ-USB2 Module for USB Computers

AVRIQ-USB2

$135.00

Discontinued
Recommended replacement: Avocent MPUIQ-VMCHS
Alternative options: Contact Us

The AVRIQ-USB2 module is one part of the AutoView switching system designed to drastically reduce cable bulk. Use the AVRIQ-USB2 module to convert keyboard, monitor and mouse signals from a server through a single CAT5 cable (up to 100 feet or 30 meters) to your switch. The AVRIQ-USB2 dongle supports a smart card reader and features virtual media functionality.

This AVRIQ interface module is the replacement for the AVRIQ-USB dongle and the AVRIQ-VMC dongle.

Avocent KVM Dongle Compatibility Table

UPC / EAN Barcode icon
UPC 636430071527
EAN 0636430071527
Question: Do they work with DSR4030
Answer: Thank you for your inquiry. This module is the replacement for the AutoView's AVRIQ series of interface modules. The replacement for the DSR famliy of KVMs' DSRIQ series, the MPUIQ-VMCHS, is found here: https://www.kvm-switches-online.com/mpuiq-vmchs.html.

Question: Will this dongle work on an AMX 5000 series KVM
Answer: Thank you for your inquiry. Unfortunately, we do not believe this is a compatible Interface module. The compatible dongle is the AMIQ series: https://www.kvm-switches-online.com/amiq-usb.html.

Question: Does this work with AutoView 3200?
Answer: Thank you for your inquiry. Yes, this interface module will work with the AutoView 3200.

Question: I have a need to extend VGA Monitor and USB Mouse for a digital video recorder about 60 feet. Could I use two of these, one on either end of Cat5e to go from the DVR without the AutoView switch? If not do you have another simple solution?
Answer: Thank you for your inquiry. Unfortunately, these CIMs (computer access modules) only operate with the KVM Switch. It sounds like you are looking for a KVM extender similar to this unit: https://www.kvm-switches-online.com/st-c5usbv-300.html. Depending on your particular needs, there are a number of options.

Question: would these work with Avocent Autoview 3016 ?
Answer: Thank you for your inquiry. Yes, this dongle will work with the Autoview 3016.

Question: Do they work with autoview 2015. Is the length 10 m ?
Answer: Thank you for your inquiry. Yes, this should work with the AutoView 2015.

In terms of length, the AVRIQ-USB module itself is significantly less than a meter. The module will need to be atatched to the AutoView via a CAT5/5e/6 cable (not ncluded). Under ideal circumstances, the CATx cable can reach out to lengths of 30 meters, so should have no problem reaching 10 meters.

Question: can these be used with the 3008, Avocent DSRIQ-USB KVM Switch USB Server Interface Module used
Answer: Thank you for your inquiry. Yes, this interface module will work with the AutoView 3008 KVM.

Question: Do this work with AutoView 2000r
Answer: Thank you for your inquiry. This is the direct replacement for the AVRIQ-USB. It should work with the AutoView 2000R.

Question: One more compatibility check; will these work with the AutoView 1515? (I have some DSRIQ-USB, but these do not work with the AutoView 1515) What is the difference between the AVRIQ-USB and the AVRIQ-USB2?
Answer: Thank you for your inquiry. According to our research, the AVRIQ-USB will work with the AV1515, which means the replacement AVRIQ-USB2 should also work. We are not 100% sure of the differences other than an attempt to consolidate and reduce the number of modules needed. The one main difference may be the addition of support for virtual media, CAC and USB 2.0.

Question: Will this dongle work with Avocent DSR1022?
Answer: Thank you for your inquiry. Unfortunately no, this dongle replaces the AVRIQ-USB and AVRIQ-VMC dongles for the Autoview KVM family.

For the DSR family, the replacement dongle is the MPUIQ-VMCHS (https://www.kvm-switches-online.com/mpuiq-vmchs.html), which replaces the DSRIQ-USB, DSRIQ-USB2, DSRIQ-USB2L, and DSRIQ-VMC dongles.

Question: Do these modules require a KVM switch, or can I just use a regular switch and software on a remote computer?
Answer: Thank you for your inquiry. Unfortunately, these modules are specifically designed for use with Avocent AutoView KVMs and are not compatible with other switches/KVMs or for use as a stand alone product.

Question: In a prior question you answered "Under ideal circumstances, the CATx cable can reach out to lengths of 30 meters," What is ideal circumstances? I need to go about 85 feet.
Answer: Thank you for your inquiry. The max distance for the cable should be around 100 feet. After that, performance can be impacted in terms of latency, video performance, etc.

In regards to ideal conditions, we are assuming use of a high-quality CATx cable (CAT6 being the best), with minimal interference, and adhering to cabling best practices. Even with less than ideal conditions, however, the AVRIQ-USB2 should work out to 100 feet; it may just require lower video resolutions.

Question: WIll this work with the Autoview 2000
Answer: Thank you for your inquiry. This is a direct replacement for the AVRIQ-USB, so it should work with the AutoView 2000. A firmware upgrade may be required.

Question: Customer has an Avocent autoview 3050 - and needs to add a server that only supports USB, the best I can tell is he needs an AVRIQ-USB which has been replaced by the USB2 model. Can you verify he can add a usb only IBM server to his 3050 with this part. Thanks for any help.
Answer: Thank you for your inquiry. The AVRIQ-USB2 is the direct replacement for the AVRIQ-USB, and supports USB and VGA connections; so all things being equal, it should fit the bill.

We have not heard of, nor seen any compatibility issues, but since all user environments vary greatly, we could not 100% guarantee compatibility.

Question: Does this work with AVOCENT AutoView 2015?
Answer: Thank you for your inquiry. The AVRIQ-USB2 is the direct replacement for the AutoView 2015's AVRIQ-USB, so it should work.

Question: Does this bundle work with avocent2000 switch
Answer: Thank you for your inquiry. This module is the direct replacement for the AVRIQ-USB and should work for all Avocent AutoView switches including the Avocent AutoView 2000.

Question: what replaces the Avocent Model AVRI-USB
Answer: Thank you for your inquiry. We are not familiar with an AVRI-USB. This unit, the AVRIQ-USB2, however, is the direct replacement for the AVRIQ-USB - a USB enabled server interface module used with Avocent AutoView KVM Switches. Could this be the model you are looking for?


Question: Will this cable work with the DSR2020?
Answer: Thank you for your inquiry. The DSR family of KVM-over-IP switches uses the DSRIQ series of modules, which have been replaced by the MPUIQ-VMCHS module located here: https://www.kvm-switches-online.com/mpuiq-vmchs.html

Question: Is there an AVRIQ module with USB and DisplayPort vice USB and VGA?
Answer: Thank you for your inquiry. Unfortunately no, there is not a DisplayPort version of the AVRIQ Computer Access Module.

Question: Will the AVRIQ-USB2 work with a USB to VGA adapter such as Cables To Go P/N 30545 or the Startech USB2VGAE2? I have a customer who has DVI-I based system that needs to be added to existing Avocent AutoView 3008.
Answer: Thank you for your inquiry. As long as the signal coming from the DVI-I system is analog, you should be able to use the Avocent VAD-27 male DVI-I to female VGA adapter. (https://www.kvm-switches-online.com/vad-27.html)

We have not attempted to use a USB to VGA type adapter, so could not comment on compatibility.

Question: Will these dongles provide Vitrual Media Support to an existing Autoview 3016
Answer: Thank yo for your inquiry. This dongle will work with the Autoview 3016. As long as the KVM has native support for Virtual Media, this dongle will provide that functionality.

Unfortunately, the AV3016 does not support remote virtual media.

Question: Will this work with the autoview 1515 model
Answer: Thank you for your inquiry. This is the direct replacement for the original AVRIQ module the AutoView series used. It should work for the AutoView 1515. However, please note it will not add Virtual Media functionality to a switch that does not natively support that functionality.

Question: Will the AVRIQ-USB2 work with an Avocent 3008 ?
Answer: Thank you for your inquiry. Yes, this interface module will work with the avocent AutoView 3008 switch.

Question: Does this work with AutoView 3100?
Answer: Thank you for your inquiry. Yes, the AVRIQ-USB2 Module will work with an AutoView 3100.

Question: Will this work on a DSR2161 KVM
Answer: Thank you for your inquiry. The replacement for the DSRIQ interface module used by the DSR2161 is the MPUIQ-VMCHS ( https://www.kvm-switches-online.com/mpuiq-vmchs.html ).

Question: Will these cables work on the Avocent 1085 model?
Answer: Thank you for your inquiry. Unfortunately, we are not familiar with an Avocent 1085 part number.

When we do a search for that part, the ECS17KMM8 rackmount console with 8-port KVM shows up most often. These Monitor keyboard drawers ship with an Avocent AutoView 3008 KVM. If the Model 1085 is part of the AutoView product family, then these should work. However, without knowing for sure which product family the 1085 is from, we could not guarantee compatibility.

Question: do they work with DAV2108
Answer: Thank you for your inquiry. Typically, these computer access modules are proprietary devices that only work with a particular manufacturer's equipment. Even through the DAV2108 may be Dell branded Avocent product, we could not say for sure that the Avocent interface module would be fully compatible with the Dell device. In any case, it would not be supported by Dell or Avocent.

To prevent loss of functionality or prevent potential damage from occurring to the switch, access modules or attached devices, we always recommend using the manufacturer's designated accessories.


Question: Does this work wih Autoview 2015?
Answer: Thank you for your inquiry,

The AVRIQ-USB2 has not been designed to work with the AV2015. You can find a full list of compatible KVM dongles and other accessories on the AV2015 page.

If you would like a recomendation based on your setup, please feel free to contact your KVM Switches Online sales reprasentative directly at 1-877-586-6654, at sales@kvm-switches-online.com, or via our online Chat functionality.

Question: Not working with Autoview 2015. Is this device compadible?
Answer: Thank you for your inquiry,

The AVRIQ-USB2 has not been designed to work with the AV2015. You can find a full list of compatible KVM dongles and other accessories on the AV2015 page.

If you would like a recomendation based on your setup, please feel free to contact your KVM Switches Online sales reprasentative directly at 1-877-586-6654, at sales@kvm-switches-online.com, or via our online Chat functionality.

Question: Will this work with the AutoView 3008?
Answer: Thank you for your inquiry,

The AVRIQ-USB2 dongle is fully compatible / meant to work with the AutoView 3008. To see a full list of manufacturer specified compatible accssories, please see the AV3008-001 page.

Question: Will this dongle work on an IBM 1735 - 3LX series KVM
Answer: Thank you for your inquiry. Typically, these types of dongles are propriety and only work with a particular manufacturer's KVM switch. In this case, this dongle is for the Avocent AutoView series only and likely wil not work in another manufactures KVM.

We are not familiar with the IBM 1735-3LX series, but we would not recommend using this dongle in a non-Avocent KVM.

Question: Do they work with the AutoView 2015
Answer: Thank you for your inquiry. Yes, this module will work with the AutoView 2015.

Question: Will these work with the autoview 2000 switch?
Answer: Thank you for your inquir,

I have confirmed that the AVRIQ-USB2 KVM dongle will indded work with the AV2000 switch.

Sorry for the delay and thank you for your patience as we updated KVMSO to a new format.

Question: Will this adapter work with the Avocent AV2015?
Answer: Thank you for your inquiry,

Yes sir, the Avocent AVRIQ-USB2 dongle is designed to work with the AV2015.

Question: will this dongle work with AV2108? and what is the life cycle of this product
Answer: Thank you for your inquiry. It appears that the Avocent avriq-usb2 will work properly with the Avocent AV2108. Stock may be depleted however as the Avocent MPUIQ-VMCHS is a newer, direct replacement of the previous. If you would like a recommendation based on your application, please feel free to contact your KVM Switches Online sales representative.

Question: Can you please send me the MTBF (mean time between faillure) value for the AVRIQ-USB2?
Answer: Thank you for your inquiry,

The MTBF (Mean-Time-Between-Failure) values for the discontinued AVRIQ-USB2 are no longer publicly available. For reference if applicable, here are the MTBF values for the replacement to the AVRIQ-USB2 (P/N MPUIQ-VMCHS):
@ 25°C, the MTBF is 9,215,740 Hours (1052 Years) with a Failure Rate (FIT) of 108.5
@ 40°C, the MTBF is 6,071,129 Hours (693 Years) with a Failure Rate (FIT) of 164.7