NTI HDMI Over Gigabit IP Extender with IR and Power over Ethernet (POE)

ST-IPHD-POELC

$156.00

Discontinued
For upgrade or replacement options: Contact Us

The NTI XTENDEX ST-IPHD-POELC Low-Cost HDMI Over Gigabit IP Extender multicasts digital video and audio signals to one or more receivers up to 393 feet away over a 1000Base-T Gigabit Network connected with CAT5e/6/7 cable.

Each Low-Cost HDMI Over Gigabit IP Extender consists of a local unit that connects to an HDMI source, and a remote unit that connects to an HDMI display. The local and remote units can be connected together for a Point-to-Point connection via CATx cable or a Point-to-Many connection via a network switch. Support for multiple transmitters requires a managed network switch.

NTI ST-IPHD-POELC Point-to-Many Extension Application Diagram

  • Supports HDTV resolutions up to 1080p.
  • Ideal solution for digital signage applications.
  • Power over Ethernet (PoE) - power supply not required at the local or remote unit.
  • Broadcast real-time HDMI video and audio signals to multiple display locations with a managed or unmanaged (also known as non-managed) network switch.
  • Support for multiple transmitters requires a managed network switch with VLAN support. Standard LAN switches can only support one transmitter.
    • Each VLAN acts as a separate HDMI Over IP Channel on the network.
    • Number of local and remote units that can be used is dependent on the backplane bandwidth of the switch.
  • Transmits an HDMI signal over one CAT5e/6/7 cable.
  • Full Infrared Remote (IR) control of HDMI source from remote HDTV using existing source remote control.
  • Plug-and-Play installation allows receivers to find the transmitter automatically on the same subnet. (Network configuration may be required for managed network switch.)
  • Web interface for firmware updates.
  • Easily expandable. Add remote units as you add monitors.
    • Supports a maximum of 253 receivers.
  • Inexpensive CAT5e/6/7 cable replaces bulky video cables.
  • Supports 10/100/1000 Ethernet connection.
  • Built-in default EDID table.
  • HDCP compliant.
  • Local and remote units must be in the same LAN. The units do not support WAN connections.

NTI ST-IPHD-POELC Use Cases

Each Low-Cost HDMI Over Gigabit IP Extender consists of a local unit that connects to an HDMI source, and a remote unit that connects to an HDMI display. The local and remote units can be connected together for a Point-to-Point connection via CATx cable or a Point-to-Many connection via a network switch. Support for multiple transmitters requires a managed network switch.

Point-to-Point Extender

Extend the video from a HDMI source + IR source up to 400ft / 120m over a single Cat6 cable (High quality cable can reach up to 500ft / 150m). By using network routers/repeaters, unlimited extension distances is also possible.

NTI ST-IPHD-POELC Point-to-point Extension Application Diagram

Point-to-Many Splitter Extender
Using a Network Router / Switch

By using a network router/switch, one ST-IPHD-L-POELC sender unit can broadcast HDMI sources to multiple ST-IPHD-R-POELC receivers. Split & extend sources effortlessly across unlimited distances.

NTI ST-IPHD-POELC Point-to-Many Extension Application Diagram

Many-to-Many Extender
Using a Managed Network Switch

Create an infinitely versatile and expandable AV matrix. By using a managed network switch, several ST-IPHD-R-POELC receiver units can access several ST-IPHD-L-POELC sender sources across the network.

NTI ST-IPHD-POELC Many-to-Many Extension Application Diagram

ST-IPHD-POELC Package Contents

NTI ST-IPHD-POELC Package Contents

  • (1) ST-IPHD-L-POELC HDMI Extender - Sender
  • (1) IR Blaster Extension Cable
  • (1) ST-IPHD-R-POELC HDMI Extender - Receiver
  • (1) IR Receiver Extension Cable
  • (1) 2-Year Standard Warranty

ST-IPHD-POELC Resources

NTI ST-IPHD-POELC Manual NTI ST-IPHD-POELC Brochure (PDF)
NTI ST-IPHD-POELC Manual (PDF)

NTI ST-IPHD-POELC Specifications

Dimensions0.94"H x 4.13"W x 3.72"D (24 x 105 x 95 mm)
Local Unit
  • One female HDMI-A port for source connection.
  • One female 1000Mbps RJ45 port for sending high definition video/audio signals and DDC signal.
  • One female 3.5mm port for IR transmitter (included).
    • IR frequency range: 20 to 60 Khz.
  • Class 3 PoE compatible (10 watts maximum).
  • Supported input resolutions: 480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz, 720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz.
  • Codec: H.264
  • Encoding delay: 22 mS at 30fps latency
Remote Unit
  • One female HDMI-A port for HDTV display.
  • One female 1000Mbps RJ45 port for receiving high definition video/audio signals.
  • One female 3.5mm port for IR receiver (included).
    • IR frequency range: 20 to 60 Khz.
  • Class 3 PoE compatible (10 watts maximum).
  • Supported output resolutions: 480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz, 720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz.
  • Supports embedded digital audio through HDMI compatible TVs or audio receivers.
Max Distance393 feet (120 meters) over Cat5e/6/7 cable.
Power
  • Power over Ethernet: With a switch that supports Power over Ethernet, a power supply is not required at the local or remote unit.
  • Local and remote unit:
    • Input: 100 to 240 VAC at 50 or 60 Hz via AC adapter (not included).
      • Country-specific AC adapter sold separately (PWR-SPLY-IPHDPOELC).
    • Output: 5VDC, 3.0A.
  • Power Consumption:
    • Local: 3.5W
    • Remote: 3.0W.
Environmental
  • Operating temperature: 32 to 140°F (0 to 60°C).
Regulatory ApprovalCE, FCC, RoHS
Warranty2-Years
Cables
  • Use HD-xx-MM cable to connect an HDMI source or display up to 50 feet away (not included).
  • Use DVI-HD-xx-MM cable to connect a DVI source or display (not included).
  • Use CAT5e/6/7 straight through cable for TIA/EIA-568B wiring terminated with standard RJ45 connectors (not included).